' How To Crack A Wi-Fi Network’s WEP Password How To Crack A Wi-Fi Network’s WEP Password | Kluwan Backtrack How To Crack A Wi-Fi Network’s WEP Password

Jumat, 19 Maret 2010

How To Crack A Wi-Fi Network’s WEP Password

First run the following to get a list of your network interfaces: airmon-ng

The only one I’ve got there is labelled ra0. Yours may be different; take note of the label and write it down. From here on in, substitute it in everywhere a command includes (interface).
Now, run the following four commands. See the output that I got for them in the screenshot below.

airmon-ng stop (interface)
ifconfig (interface) down
macchanger –mac 00:11:22:33:44:55 (interface)
airmon-ng start (interface)
If you don’t get the same results from these commands as pictured here, most likely your network adaptor won’t work with this particular crack. If you do, you’ve successfully “faked” a new MAC address on your network interface, 00:11:22:33:44:55.
Now it’s time to pick your network. Run:
airodump-ng (interface)
To see a list of wireless networks around you. When you see the one you want, hit Ctrl+C to stop the list. Highlight the row pertaining to the network of interest, and take note of two things: its BSSID and its channel (in the column labelled CH), as pictured below. Obviously the network you want to crack should have WEP encryption (in the ENC) column, not WPA or anything else.
Like I said, hit Ctrl+C to stop this listing. (I had to do this once or twice to find the network I was looking for.) Once you’ve got it, highlight the BSSID and copy it to your clipboard for reuse in the upcoming commands.
Now we’re going to watch what’s going on with that network you chose and capture that information to a file. Run:
airodump-ng -c (channel) -w (file name) –bssid (bssid) (interface)
Where (channel) is your network's channel, and (bssid) is the BSSID you just copied to clipboard. You can use the Shift+Insert key combination to paste it into the command. Enter anything descriptive for (file name). I chose "yoyo", which is the name of the network name I'm cracking.

You'll get output like what's in the window in the background pictured below. Leave that one be. Open a new Konsole window in the foreground, and enter this command:
aireplay-ng -1 0 -a (bssid) -h 00:11:22:33:44:55 -e (essid) (interface)
Here the ESSID is the access point’s SSID name, which in my case is yoyo. What you want to get after this command is the reassuring “Association successful” message with that smiley face.

You’re almost there. Now it’s time for:
aireplay-ng -3 -b (bssid) -h 00:11:22:33:44:55 (interface)
Here we’re creating router traffic to capture more throughput faster to speed up our crack. After a few minutes, that front window will start going crazy with read/write packets. (Also, I was unable to surf the web with the yoyo network on a separate computer while this was going on.) Here’s the part where you might have to grab yourself a cup of coffee or take a walk. Basically you want to wait until enough data has been collected to run your crack. Watch the number in the “#Data” column—you want it to go above 10,000. (Pictured below it’s only at 854.)
Depending on the power of your network (mine is inexplicably low at -32 in that screenshot, even though the yoyo AP was in the same room as my adaptor), this process could take some time. Wait until that #Data goes over 10k, though—because the crack won’t work if it doesn’t. In fact, you may need more than 10k, though that seems to be a working threshold for many.

Once you’ve collected enough data, it’s the moment of truth. Launch a third Konsole window and run the following to crack that data you’ve collected:
aircrack-ng -b (bssid) (file name-01.cap)
Here the filename should be whatever you entered above for (file name). You can browse to your Home directory to see it; it’s the one with .cap as the extension.
If you didn’t get enough data, aircrack will fail and tell you to try again with more. If it succeeds, it will look like this:
The WEP key appears next to “KEY FOUND.” Drop the colons and enter it to log onto the network.

Problems Along the Way

With this article I set out to prove that cracking WEP is a relatively “easy” process for someone determined and willing to get the hardware and software going. I still think that’s true, but unlike the guy in the video below, I had several difficulties along the way. In fact, you’ll notice that the last screenshot up there doesn’t look like the others—it’s because it’s not mine. Even though the AP which I was cracking was my own and in the same room as my Alfa, the power reading on the signal was always around -30, and so the data collection was very slow, and BackTrack would consistently crash before it was complete. After about half a dozen attempts (and trying BackTrack on both my Mac and PC, as a live CD and a virtual machine), I still haven’t captured enough data for aircrack to decrypt the key.http://www.lifehacker.com.au/2009/07/how-to-crack-a-wi-fi-networks-wep-password-with-backtrack/

Anda Sudah Baca Yang Ini? :

WEP
Label: , , ,

0 komentar:

Klik Here To Show All Comment


Posting Komentar

newer page older page home
Langganan: Posting Komentar (Atom)
top